Cooler Master MWE Gold 850 V2 Full Modular

An 850 W fully modular ATX power supply with 80 PLUS Gold efficiency, a 120 mm hydrodynamic-bearing fan, two EPS connectors and a five-year warranty.

Cooler Master MWE Gold 850 V2 Full Modular

Full Specification Sheet

Wattage850 W
Form FactorATX (160 x 150 x 86 mm)
StandardATX 12V Ver. 2.41
Efficiency80 PLUS Gold, 90% at typical load
ModularityFully modular
Fan120 mm, hydrodynamic bearing (HDB), 1500 RPM
Noise0 dBA at 20% load, 17.8 dBA at 50%, 25.9 dBA at 100%
Connectors1x 24-pin, 2x EPS (4+4 and 8-pin), 4x PCIe 6+2, 12x SATA, 4x Molex
Hold-up Time16 ms at 100% load
Warranty5 years

The Cooler Master MWE Gold 850 V2 Full Modular is an 850-watt ATX power supply from the company's MWE Gold series, a line that aims at builders who want 80 PLUS Gold efficiency and fully modular cabling without moving into the premium price tier. It is the V2 revision of the original MWE Gold, upgraded with a hydrodynamic-bearing fan, a higher operating-temperature limit and two EPS connectors as standard. Note that this model follows the ATX 12V version 2.41 standard rather than the newer ATX 3.x standard, a difference that matters for graphics cards with the 16-pin power connector, and one that this page explains in detail. It is a straightforward, conventional unit, and the published specification is clear and complete enough to judge exactly what it will and will not power.

Rated power and efficiency

The unit is rated at 850 W and carries the 80 PLUS Gold certification. Cooler Master states an efficiency of 90 percent at typical load and describes 80 PLUS Gold as guaranteeing a typical minimum of 90 percent efficiency. Efficiency describes how much of the power drawn from the wall reaches your components rather than being lost as heat, so a Gold unit wastes less energy and produces less heat than a Bronze one at the same output. Active power factor correction is fitted, and the unit accepts an input of 100 to 240 volts at 50 to 60 Hz, with a stated input current of 12 to 6 amperes, so it works on both 115 V and 230 V mains. The unit also complies with the ErP 2014 Lot 3 requirements. To understand how the efficiency tiers differ, see our explanation of 80 PLUS Bronze versus Platinum efficiency.

Cooler Master also lists a power-good signal of 100 to 150 milliseconds, a hold-up time of 16 milliseconds at 100 percent load and a mean time between failures of 100,000 hours. Hold-up time is how long the unit keeps its outputs within specification after mains power is lost, and 16 ms is the figure that the ATX design guide expects. The MTBF is a manufacturer-stated statistical figure, not a guarantee of lifetime.

Connectors and modular cabling

The 850 V2 is fully modular: all cables, including the main 24-pin, detach from the unit. Cooler Master says the cable set is flat and black, and the practical benefit is that you install only the cables your system needs, which reduces clutter and helps airflow. The published connector counts are one 24-pin ATX connector, two EPS connectors (one 4+4 pin and one 8-pin), four PCIe 6+2 pin connectors, twelve SATA connectors and four 4-pin peripheral (Molex) connectors. Cooler Master highlights the two EPS connectors as a compatibility feature, since some high-end boards need two 8-pin CPU power inputs. The arrangement of connectors and the cable choices are discussed in our guide to modular power supplies and cable management.

The four PCIe 6+2 connectors are the item to check against your graphics card. They are suited to cards with one, two or three 8-pin inputs, and the largest cards with four 8-pin inputs would use all four. A graphics card with the newer 16-pin connector needs an adapter, and because this unit has no native 12V-2x6 cable and does not follow the ATX 3.x standard, you should read the graphics card's own power recommendations before pairing them. Many modern cards in the 200 to 300 W range still use 8-pin connectors and pair without issues.

Fan, noise and temperature

Cooling is provided by a 120 mm fan with a hydrodynamic bearing (HDB), rated at a maximum of 1,500 RPM. Cooler Master says the V2 has been upgraded to the HDB fan, giving quiet, effective cooling and a long lifespan, and that additional measures were applied to reduce sound output and ripple noise compared with the original. The published noise levels are 0 dBA at 20 percent load, 17.8 dBA at 50 percent load and 25.9 dBA at 100 percent load. Those are manufacturer-stated measurements under Cooler Master's test conditions and will differ in a real case, but they show the intended behaviour: near-silent at low load and still modest at full output. The operating temperature range is 0 to 50 degrees Celsius; Cooler Master notes that the original MWE Gold was limited to 45 degrees and that the V2 adds five degrees of headroom, which helps in warm rooms and in compact cases.

Protections and certifications

The listed protection set is undervoltage, overvoltage, overpower, overtemperature, short-circuit and overcurrent protection (UVP, OVP, OPP, OTP, SCP and OCP). Regulatory approvals include TUV, CE, CCC, EAC, RCM, cTUVus, FCC, BSMI and UKCA. The unit measures 160 by 150 by 86 millimetres, the standard ATX size, and it is backed by a five-year manufacturer warranty from the date of purchase.

Reading the ATX 12V 2.41 label

The standard a power supply follows determines its connector set and some of its behaviour. ATX 12V version 2.41 is the long-established design, and it is completely adequate for systems built around 8-pin PCIe connectors and standard EPS CPU cables. Units that follow the newer ATX 3.x specification add a native 16-pin cable and tolerance for short power spikes, which is why they are the usual pairing for the latest high-power graphics cards. If your card ships with a 16-pin adapter that converts several 8-pin inputs, this unit can still power it, provided you have enough free PCIe cables; the unit lists four. If your card needs more than the available connectors, a newer ATX 3.x unit is the more comfortable choice.

Ventilation and placement

Because the fan bearing is hydrodynamic and the unit is rated to 50 degrees Celsius, placement is forgiving, but the usual advice applies: leave the intake side of the power supply with a clear path to fresh air, keep dust filters clean and avoid blocking the exhaust when the unit sits in a bottom shroud. The published noise figures assume the fan responds to load, so a well-ventilated case that keeps the unit cooler will generally keep it quieter as well.

What it suits and how it compares

An 850 W rating gives comfortable room for a mainstream gaming system with a strong graphics card and a modern processor, and it is a sensible choice for builders who want headroom for later upgrades. For guidance on choosing a wattage for your own configuration, our guide to power supply wattage describes how to add up component demands and leave a margin. Among other units on this site, you can compare it with the Corsair RM850x on the MWE Gold 850 V2 versus RM850x comparison page, which is a more recent Corsair design, or with the entry-level MWE Gold 850 V2 versus Corsair CX600M comparison to see how much a fully modular Gold unit adds. More options are listed in the power supply category.

All figures on this page are taken from Cooler Master's official product specification. Prices and warranty terms vary by market and retailer, so confirm the details before you buy, and always match the connectors of a power supply to those on your components rather than relying on wattage alone.

Product image: Cooler Master product image.